Home
JAQForum Ver 24.01
Log In or Join  
Active Topics
Local Time 12:23 21 Oct 2026 Privacy Policy
Jump to

Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me.
Forum Index : Windmills
  Topics Started By Replies Views
Last Post By
Sticky Topics        
Forum upgrade Gizmo, 05/07/2019 314 365492 wiseguy  04:07am 12 Dec 2025
Forum Guidelines Gizmo, 11/12/2011 2 534547   02:49pm 16 Dec 2015
Normal Topics  

   Page 30 of 99    

No Forum Smokey5159, 11/07/2011 10 4719   10:40pm 18 Jul 2011
How to get equal prop angle? domwild, 17/07/2011 3 5264   11:03pm 17 Jul 2011
Help please Smokey5159, 10/07/2011 7 5656   08:05pm 17 Jul 2011
My new mill VK4AYQ, 06/09/2010 176 157587   03:55am 16 Jul 2011
What is this? AMACK, 04/02/2011 10 5769   05:15am 15 Jul 2011
grid tie inverter for windmill Xmaswiz, 10/06/2011 20 10472   09:56pm 11 Jul 2011
12 or 24 Volt car alternator mill? VK6MRG, 10/07/2011 7 6541   11:15am 11 Jul 2011
VAWT WALL rissole, 10/07/2011 1 4276   10:22pm 10 Jul 2011
White Pointer AXFX Trev, 05/01/2011 55 56383   03:16pm 10 Jul 2011
PhillM dual kicking butt for KarlJ! KarlJ, 10/07/2011 2 4079   01:24pm 10 Jul 2011
Wind turbine noise solution barrygun, 03/07/2011 10 7335   04:28pm 09 Jul 2011
Little help please i8unwo, 29/06/2011 3 5253   01:00pm 09 Jul 2011
Going were no turbine has gone before Tow BobMann, 09/07/2011 2 4686   12:38pm 09 Jul 2011
An answer if I may Smokey5159, 09/07/2011 3 4650   12:40am 09 Jul 2011
inverterless solution vawtwindy, 04/07/2011 3 4841   09:06am 04 Jul 2011
Vawt - grid / mains connection Ynot, 03/07/2011 6 4597   09:02am 04 Jul 2011
cutting Magnets brucedownunder2, 07/06/2011 6 6078   11:47pm 02 Jul 2011
To re-wire or not re-wire Smokey5159, 02/07/2011 3 4162   11:10pm 02 Jul 2011
Simple Windmill/Solar controller bertech, 27/06/2011 3 3980   01:48pm 01 Jul 2011
What set-up? Smokey5159, 28/06/2011 5 5338   04:00pm 30 Jun 2011
Installation red tape Rastus, 24/06/2011 17 6154   02:20pm 30 Jun 2011
2 Stage Cutin Coils Idea. Downwind, 31/10/2010 19 18669   11:21am 28 Jun 2011
Chinese Ouyad Electronics Ltd 2Kw WT jimisbell, 28/06/2011 0 3455   05:13pm 27 Jun 2011
MacGyver Ax-Fx Build MacGyver, 19/05/2010 119 100640   02:39pm 27 Jun 2011
EMC Compliance required? darcyrandall200, 19/06/2011 6 4638   07:14am 26 Jun 2011
= New posts since you last visited .      

   Page 30 of 99    

The Back Shed's forum code is written, and hosted, in Australia.
© JAQ Software 2026