Home
JAQForum Ver 24.01
Log In or Join  
Active Topics
Local Time 14:27 24 Apr 2026 Privacy Policy
Jump to

Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me.
Forum Index : Windmills
  Topics Started By Replies Views
Last Post By
Sticky Topics        
Forum upgrade Gizmo, 05/07/2019 314 201692 wiseguy  04:07am 12 Dec 2025
Forum Guidelines Gizmo, 11/12/2011 2 518368   02:49pm 16 Dec 2015
Normal Topics  

   Page 63 of 99    

car starter motor used as generator? iguana9999, 07/02/2009 6 13536   02:49am 07 Feb 2009
7.5HP Three Phase Motor Conversion SparWeb, 24/09/2008 54 32583   08:50pm 06 Feb 2009
miniture DaViD, 05/02/2009 4 3223   03:39pm 06 Feb 2009
no juice... birdhouse, 05/02/2009 5 2962   03:53pm 05 Feb 2009
motor DaViD, 06/02/2009 0 2719   03:08pm 05 Feb 2009
Neo conversion brucedownunder2, 03/02/2008 51 15062   02:52am 05 Feb 2009
Wiring for Savonius? Mr.Sleepy, 29/01/2009 13 4991   08:39pm 03 Feb 2009
Simple and accurate RPM measurement imsmooth, 31/01/2009 4 3578   06:37am 03 Feb 2009
10.5’ cedar/epoxy blades flying imsmooth, 02/02/2009 1 3380   05:10am 03 Feb 2009
Fisher & Paykel model preference catchnthe-)))), 01/02/2009 0 2847   03:56am 01 Feb 2009
Windmill System crazyk, 29/01/2009 16 4421   08:48am 31 Jan 2009
another newbie question birdhouse, 29/01/2009 15 4421   11:30pm 30 Jan 2009
blade weight comparing catchnthe-)))), 21/01/2009 6 3074   12:23pm 30 Jan 2009
Motor crazyk, 28/01/2009 6 3454   01:10am 30 Jan 2009
motion conversin question! faroun, 29/01/2009 6 2769   01:01am 30 Jan 2009
Windmill Build - Wooden Blades - Scotland Gavztheouch, 29/01/2009 4 3969   10:42pm 29 Jan 2009
Windshield Motor crazyk, 29/01/2009 2 2792   10:03am 29 Jan 2009
Attaching hub to shaft caesius, 26/01/2009 2 3285   12:03am 29 Jan 2009
good size of blades for my new motor?? birdhouse, 27/01/2009 4 2789   01:13am 28 Jan 2009
ebay DaViD, 23/01/2009 2 3086   06:52am 26 Jan 2009
Lift force catchnthe-)))), 24/01/2009 5 2847   02:09am 26 Jan 2009
Carving a Wind Mill Blade Gavztheouch, 24/01/2009 2 3075   09:05pm 23 Jan 2009
12 volt heater element newbie-from-pa, 01/08/2008 11 10101   07:36pm 23 Jan 2009
Wave Wound Axial Generator wdyasq, 20/01/2009 20 37886   11:35am 23 Jan 2009
Question about gizmo’s plan; RE: shaft caesius, 23/01/2009 1 3052   11:04am 23 Jan 2009
= New posts since you last visited .      

   Page 63 of 99    

The Back Shed's forum code is written, and hosted, in Australia.
© JAQ Software 2026