TheBackShed.com

Home	JAQForum Ver 24.01
Log In or Join
Active Topics
Local Time 17:17 23 Jul 2026	Privacy Policy
Jump to

Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me.

Forum Index : Windmills

New Topic

	Topics	Started By	Replies	Views	Last Post By
Sticky Topics
	Forum upgrade	Gizmo, 05/07/2019	314	344695	wiseguy 04:07am 12 Dec 2025
	Forum Guidelines	Gizmo, 11/12/2011	2	527470	02:49pm 16 Dec 2015
Normal Topics			Page 74 of 99
	13ft problem	aussiekiwi, 22/05/2008	12	4498	04:18am 29 May 2008
	Get-together	nice_pak2002, 28/05/2008	1	3631	09:00pm 28 May 2008
	first time post	wandyhee, 27/05/2008	4	3806	03:29am 28 May 2008
	Angle of attack	CB365, 27/05/2008	2	3580	11:39pm 27 May 2008
	Completely new... no idea where to start	computerguy, 26/05/2008	4	4882	11:32pm 25 May 2008
	Blowing in Brisbane - 3.796 KWh	fillm, 18/05/2008	5	5852	11:57am 25 May 2008
	7 phase F&P using hard drive magnets	spiral, 06/05/2008	34	18260	10:48am 25 May 2008
	Beginning	nice_pak2002, 23/05/2008	4	3583	10:43am 25 May 2008
	dismantling chinese windmill..	Steve9R, 25/05/2008	1	3377	09:35am 25 May 2008
	formula question	dazz, 25/05/2008	2	3283	01:25am 25 May 2008
	SMFIS	dazz, 21/05/2008	14	4108	03:52pm 24 May 2008
	I-beam tower?	imsmooth, 24/05/2008	2	3639	07:09am 24 May 2008
	Blade design	311fan, 21/05/2008	11	5029	01:52pm 22 May 2008
	Mounting the Bearings for Randy�s Weldmen	imsmooth, 19/05/2008	0	3247	10:14pm 18 May 2008
	25 rotor turbine	azland00123, 16/05/2008	5	3347	07:19pm 17 May 2008
	Testing the neo rotor	imsmooth, 14/05/2008	6	5089	06:49am 15 May 2008
	F&P Newbie	RevUpWind, 03/05/2008	3	3934	11:43pm 14 May 2008
	Use a ventilator/Savonius?	jlsawell, 13/05/2008	2	4739	02:56am 13 May 2008
	swept area of savonius rotor	ewells13, 07/05/2008	4	8731	07:08am 08 May 2008
	Controller recommendations ?	Steve9R, 07/05/2008	2	5185	11:57pm 07 May 2008
	emergency stop mechanism	imsmooth, 06/05/2008	9	4143	02:50am 07 May 2008
	Blade Balancing	suitep123, 06/05/2008	3	4777	08:32am 06 May 2008
	DIY job	craft, 03/05/2008	12	4713	08:04am 05 May 2008
	Project update	CanTinker2, 28/04/2008	18	5555	03:40am 03 May 2008
	2 new projects	rber, 01/05/2008	3	3793	03:39am 03 May 2008
= New posts since you last visited .

Page 74 of 99